POWERHOUSE PRODUCTS

New!! Stand Alone Precision Mini Digital Launch/Shift Lights
New!! "Gann" Style Pro Clutch
New!! Block Off Plates For 2008 Hayabusa
New!! Billet Fuel Rail For 2008 Hayabusa
Electric Water Pump For Hayabusa

TIC-1000 - IN STOCK!!!
Hayabusa Oil Pump Gear
Hayabusa Heavy Duty Billet Ouput Shaft
NEW!! SHINKO 003 Ultrasoft Tire

Dynojet Power Commander
BEST Aluminum Polish - "The Brooklyn Ball Buster"

Stand Alone L.E.D. Shift Lights
New!! POWERHOUSE L.E.D. Launch Light!!!
MSBC-1 Boost Controller
AMS-1000 Boost Controller
Two-Stage Boost Controller
Carrillo H-Beam Rods For The Hayabusa
NEW!! Carrillo H-Beam Rods For ZX10/ZX12/ZX14/GSXR1000
Turbo Hayabusa Plenum Tie-Down Modification Kit
Stainless Steel Throttle Blades For Hayabusa
Condor Pit Stop/Trailer Stop
New!! ARP 10mm Stud Kits - IN STOCK!

 

New!! Dynojet Multi-Function Hub - IN STOCK!
Call for pricing...

Click for larger image

Click for larger image

Click for larger image

 


 


New!! "Gann" Style Pro Clutch:

The BEST drag clutch setup out there right now!

Hand operated, smoother than a multistage!

Legal in AMA Prostreet . . .

Along with this clutch you will need a slider outer
basket and an inner hub, bearing kit and shim kit to
set this up properly . . .

POWERHOUSE PRICE: $1200.00 USD


Click for larger image

Back To Top

 


 

New!! Dynojet Color LCD Display - IN STOCK
Call for pricing...

Click for larger image

Back To Top


 


Click for larger image

The Tic-1000 kit comes with TIC-1000 control unit,
harness, IKU-1 kill box, connectors and instruction manual
$ 850.00

 

TIC-1000

Shift light output programmable for each gear
Launch light output
2 step
anti-lag for turbos
ignition retard based on manifold pressure and/or gear
shift counter
auto shift
shift kill programmable for each gear
dedicated shift solenoid output
inputs are polarity programmable
billet aluminum enclosure( same size and look of the
ams-1000 controller)
terminal strips for secure connections
delay timer...when this function is activated it will
hold the retard amount that is
programmed under the antilag setting until clutch
input is removed.
It will then refer to the amount of time that is
programmed and phase the
timing from the retarded amount to full advance by the
end of time programmed.
- 0-5 seconds
- example
* anti lag programmed for 8 degrees retard.
delay timer of 3 seconds
clutch input is removed timing goes from 8 degrees of
retard to 0 in 3 seconds


Back To Top

IKU-1 Kill box Features:
Its back!

terminal strip terminations
5 milli second programmability from 25-120 milli
seconds
ground activated
NLR exclusive DIGITAL kill design for repeatable,
fast, reliable shifts!
Designed to integrate with TIC-1000. Once connected
the TIC takes complete control over kill time.
This is a ignition kill control unit NOT a 2 step.

Can be purchased as a standalone kill unit $199.95

 

 

 


Click for larger image

HAYABUSA OIL PUMP GEAR

Powerhouse now stocks the new high volume oil pump
gear for the Suzuki Hayabusa. It is no secret that the mighty Hayabusa has a problem with low oil pressure. This new gear is a direct bolt in replacement for the OEM oil pump gear. This gear causes the pump to turn at faster speeds which increases oil volume and pressure.

Initial testing revealed the following improvements:
3,000 RPM, 32 psi with stock gear, 52 psi with high volume gear; 6,000 RPM, 72 psi stock, 90 psi with high volume gear.

Another "must have" item for ALL Hayabusas.
Powerhouse Price - $110.00

Back To Top

 


 

Click for larger image

Suzuki Hayabusa Heavy Duty Billet Ouput Shaft

The last thing you need on that big horsepower 'Busa is a stock output shaft. We have seen the stock output shaft break under a heavy load, causing you not only to lose, but also to do damage to your bike.

This Heavy Duty Output Shaft is machined from super high strength aircraft alloy steel. The sprocket spline area has been increased from 25mm to 30mm, and accepts commonly available countershaft sprockets.

This part is a direct bolt in, and requires no modifications to the cases or transmission gears. It
is supplied with a 16 tooth sprocket and spacer, with 15-18 tooth sprockets also being available.

Order it now from Powerhouse: $365

Back To Top

 


Click image for a better view

NEW!! Shinko 003 Ultra Soft

A new, softer version of the popular 003 Shinko!
Lighter than the original, great for the track -
Finally, a tire you can put on that turbo bike AND
race at the strip with! In stock, $160

 

Powerhouse Price: $149 (190/50-17)

Back To Top

 


 

 

Powerhouse Motorcycles "web only" special...

Mention this ad and get 10% off a
Dynojet Power Commander!

Back To Top

 


 

BEST Aluminum Polish - "The Brooklyn Ball Buster"

This is absolutely the BEST aluminum polish we have found to date. Keeping your polished bike looking like the day you got it has always been a chore - until now.

Brooklyn Ball Sauce is like a showroom detailer for your aluminum. Wipe on, wipe off - using Bounty paper towels - and your aluminum will always look like chrome. Quick, easy, and the result is brilliant! Polish your rocket, yes, but don't polish it all day; this product will save time and enable you to take it out and play with it too...


Click images above to see the results of using this fantastic product.
CAUTION: File sizes are extremely large so you can see the quality detailing you can do using Brooklyn Ball Sauce
. The bike frame and swingarm pictured here are aluminum!

Powerhouse price: $16/bottle

Back To Top

 


 




Click images for a better view
STAND ALONE L.E.D. SHIFT LIGHTS

These things are great - small enough to mount up on
your Hayabusa dashboard under the windshield . . .

This is a "stand alone" unit - you DO NOT need a Dyna
Shift minder (approx. $125), or the tach adaptor that
goes with it (approx. $30), PLUS a shift light . . .

All you need is this L.E.D. shift light: three wire
hookup, set the dials for the proper RPM, and off you
go.

Available in a variety of colors, only $109.95 + S/H
(Blue L.E.D.s & chrome slightly extra)

Back To Top

 


 




Click images for a better view
POWERHOUSE L.E.D. LAUNCH LIGHT

Not a shift light, a launch light for those who need a
light for their TIC-1000 box, or any other application
where a 12V trigger is used . . .

Available in yellow or red L.E.D. $45.00 + $7.00 S/H

Back To Top

 

 


 




Click images for a better view
STAND ALONE PRECISION MINI DIGITAL LAUNCH/SHIFT LIGHTS

The Raptor shift light has been a hit with the late model, distributor-less engines while still working well with old points type ignitions. It's ease of use, compact size, and the fact that no rpm converters or adaptors are required, has allowed it to become the most popular shift light on the market today! Make your launch consistent with the aid of a Raptor dual mode launch/shift light! Our newest edition of shift lights for 2008, incorporates a launch feature as well as the features in our standard shift light.

POWERHOUSE PRICE - $129.99 + S/H

Back To Top

 


 

 



Click for a better view
MSBC-1 BOOST CONTROLLER

* Six stage programmable boost control
* 0-60 PSI target boost range for each stage, in 1 PSI increments
*
9 different ramp settings per stage, which control how fast boost is allowed to build
* Interfaces with OEM Gear Position Sensor (GPS)
* Shift input for drag racing
* Readout of actual boost during boost control
* Two solenoid drive outputs (increase/decrease)
* Can be used with single or dual port wastegates
* Uses electronic pressure sensor to control boost by monitoring manifold or wastegate pressure
* Can be used with manifold pressure only or external pressure source for control air

POWERHOUSE PRICE: $650.00

Back To Top

 




Click for a better view
AMS-1000 BOOST CONTROLLER

This is the controller used by the world's quickest and fastest turbo motorcycles - also used by the world's quickest and fastest Nissan, Vinny Ten's 350Z...

AMS-1000 features:

* Billet aluminum enclosure
* Operates in ice-cold conditions
* Shock proof
* Tested in high heat
* Waterproof
* Terminal strip for neat and secure connections
* Will adjust itself when input pressure has changed in order to deliver the most accurate ramping and target termination
* Comes with 60 PSI stainless sensor
* Launch mode programmable from 0-60 PSI
* Scramble boost - will increase pressure to user setting regardless of programming
* Reduce boost - will decrease pressure
* Multiple operating modes:
** Time based: up to 6 stages
** Shift input: up to 6 stages
** GPS: up to 6 gears

POWERHOUSE PRICE: $850.00

Back To Top

 


 



Two-Stage Boost Controller

If you have ridden a turbo bike with high power, you already know what a handful it can be under some conditions, especially with a stock wheelbase.

This electric boost controller gives you access to two boost levels, making your bike more controllable and more rideable at the sametime.

High boost is adjustable, and is attained by supplying 12V to the controller. Most customers add a
small toggle switch or use an existing switch to activate the controller.

You can now run your bike on pump gas at low boost, add good fuel, flip the switch, and go right to high boost . . .

POWERHOUSE PRICE: $229.95 + S/H
Back To Top

 




Click for a better view
CARRILLO H-BEAM RODS FOR THE HAYABUSA

These are the "Pro H Beam" rods with the SPS
Multiphase bolts.
Everyone knows that the Carrillo
H-beams are the world's strongest rods, and that these
are a must for turbo or nitrous motors going over 400
HP.

We have race-tested these rods and have gone as
high as 315 horsepower PER ROD,
and they still look
brand new...


Set of 4 - List Price $1350.00
POWERHOUSE PRICE: $1149



Back To Top

 


 

Click images for a better view

TURBO HAYABUSA PLENUM TIE-DOWN MODIFICATION KIT

Is your turbo plenum and/or throttle bodies coming out of your manifolds because of high boost? Although we originally came up with these for Hahn Racecraft kits, we have found they are adaptable to a number of other brands . . .


Absolutely necessary for any boost over 15 pounds.


Click image above to get a better view post-installation...

Kit includes two aluminum tabs to weld on to your
existing plenum, AIRCRAFT-QUALITY turnbuckles, and a pair of anchor plates that go over your cylinder head engine mounts . . .

POWERHOUSE PRICE: $120.00

Back To Top

 




Click for a better view
STAINLESS STEEL THROTTLE BLADES FOR HAYABUSA

It is no secret that good replacement throttle blades
are very hard to find for the Hayabusa. There are
several "big name" "race" distributors selling
absolute crap
- ill-fitting, sloppily machined
throttle plates that cannot be synchronized and make
your bike idle at 2,000 rpm.

Our throttle blades are NOT "made in the USA", and in this case, thats good!

POWERHOUSE PRICE: $135



Back To Top

 


 


Click for a better view

BLOCK OFF PLATES FOR 2008 HAYABUSA

Eliminate the clean-air system on your 2008 Hayabusa with these
block off plates from POWERHOUSE. . . Only $39.95

Back To Top

 

 


BILLET FUEL RAIL FOR 2008 HAYABUSA

This new billet fuel rail is for your stock injectors, and not only does it give you access to your fuel system, but it increases flow, has -6AN fittings, and will allow you
to run an external fuel pump . . .

POWERHOUSE PRICE: $269.00

Note: finished rail will be black anodized.


Click for a better view


Click for a better view


Click for a better view

Back To Top


ELECTRIC WATER PUMP FOR HAYABUSA

This electric water pump flows 5 gallons per minute and draws less than 1 amp.
The billet housing bolts right into the stock location, using your stock hoses
and no modifications. It greatly reduces your engine temps in stop and go traffic,
as the water circulates at the same rate all the time. Using a switched
radiator fan, you can run this pump and the fan with the bike not running
to cool it down on a hot day, or after a pass. There is enough clearance for billet
sprocket covers, slave supports, or cable conversions.
Great for motor bikes, nitrous bikes, and especially for turbo bikes!

POWERHOUSE PRICE: $525.00 including shipping in the U.S.


Click for a better view


Click for a better view


Click for a better view

Back To Top


 




Click images for a better view
CONDOR PIT STOP/TRAILER STOP

 

This fully adjustable wheel locking system is
capable of accomodating either front or rear wheels in
sizes from 15-22" or 80-220 mm wide.

The patented locking mechanism securely supports
your motorcycle in an upright position on any type of
flat surface or transport platform.

The Pit Stop also serves as a Trailer Stop with the
optional Trailer Adaptor kit, which allows quick
attaching or detaching.

Requires only one person to load or release any
motorcycle and in most cases, 2 tie-down straps are
required to secure the bike for transport.

Can be placed directly on ground, enabling you to
ride your bike right into the Condor stop, holding the
bike straight up without any other stand or side
stand.

Condor Pit Stop $235.00
Trailer kit for Pit Stop $20.00

Back To Top

 


Call POWERHOUSE MOTORCYCLES for ALL your Carrillo rod needs:
Car or bike, American or foreign, watercraft,
dirt bike, ATV, etc . . . POWERHOUSE has you covered!

Carrillo H-Beam rods for ZX14 on sale: $1075.00

Carrillo H-Beam rods on sale:

2008 Suzuki Hayabusa: $1149.00
1999-2007 Suzuki Hayabusa: $1149.00
2005-2006 Suzuki GSXR1000: $1149.00
2004-2006 Kawasaki ZX10: $1170.00
2000-2005 Kawasaki ZX12: $1149.00


Click for larger image

Back To Top


 

All products sold by Powerhouse Motorcycles are intended for off-road or racing use only, and as such, no warranty is expressed or implied.

Do it right the first time - at Powerhouse.
...Home of the 750HP Motorcycle Dyno...
111 Jersey Street - West Babylon, NY - 11704
Certified N.Y.S. Motorcycle Inspection Station
powerhouse@fastcycles.com
(631)491-6767

© 2004 - 2008 - All images and content on this site copyright of Powerhouse Motorcycles, New York. Unauthorized use of these images or content without written permission of Powerhouse Motorcycles, New York is an infringement of copyright law and will result in legal action. All rights reserved as protected by Federal copyright laws.